King 3.0 Bypass Shock
HM4X4 is an official King Shocks dealer and service center.
King's bypass shock absorber technology, a project born over 10 years ago, regardless of your needs can provide specific bypasses to ensure complete suspension control at high and low speeds.
Bypass shocks are a top of the line performance, for your off-road vehicle, as long as they are configured correctly. With the correct shock body size, stroke length, bypass tube arrangement and tuning, they can be incredible for the most demanding off-road driving.
Bypass shocks work by allowing oil to flow through tubes around the shock's main piston. Each tube contains a check valve that allows oil to flow in only one direction. By stacking the bypass tubes around the body at different heights, the shock absorber has softer zones and stiffer zones. The stiffness of each zone is controlled by the diameter of the bypass tube and the opening of the check valve (external adjustment).
Bypasses are position sensitive; it is possible for the tubes to be positioned incorrectly, which can make the shock absorber too stiff and jarring, too soft and bouncy, or even non-adjustable.
The height position of the bypass tubes relative to the piston is very important for proper operation. For a 2-tube bypass shock absorber, there are mainly 3 zones where the shock absorber will be affected by the valve and compression tubes:
the Bump Zone is the zone where the shock absorber is close to full lowering and the piston has passed all the bypass tubes;
the Ride Zone is the zone where the vehicle will be at trim height and where it will move most of the time;
the Top Out Zone is when the shock absorber is fully extended and the piston has passed all the extension tubes.
Likewise, the performance of a bypass shock absorber is dictated by its tuning. Tuning in all shock absorbers refers to our ability to control the force of the shock absorber over a wide range of shaft speeds. For example, shock absorbers that do not run enough oil move poorly because oil flowing through a fixed bore increases forces exponentially. The same happens with bypasses when the internal valve is stiff and the tubes are too small. For this reason, it is important that the vehicle be equipped with the correct bypass damper, assuming a bypass damper is needed.
Bypass shocks have hard zones and soft zones. Without an adequate amount of upward travel, there is no room for each zone to do its job well and you can end up with shocks that are too soft or too stiff. Therefore, for suspensions with less than 5″ of maximum stroke, bypass shocks are not recommended.
Bypass shocks are designed for off-road performance. If you are looking for the best ride on the road and do not plan to do demanding off-road riding, bypass shocks may not be the best choice for you.
Bypass shocks can be ordered with different compression and rebound bypass tubes. In general, the more tubes, the more adjustable the shocks are.
2-tube bypass shocks
2-tube bypass shocks generally have one compression and one rebound tube. The rapid transition between the travel zone and the shock zone can be aggressive.
3-tube bypass shocks
Also called triple bypass shocks, these are by far the most common configuration. The extra compression tube helps make the compression zones smoother.
4-tube bypass shockss
Adding the fourth tube in extension really helps control and is highly recommended for most axle applications, where over-extension can be a problem.
King 3.0 PR Series Bypass Shocks are the largest and longest travel shocks King offers before stepping up to their Trophy Truck series shocks. These massive 3.0 body shocks are available with up to 4 bypass tubes and feature an oversize 1" diameter shock shaft. With the ability to handle the workload of two 2.5 body shocks, these 3.0 bypass shocks are purpose built for extra large vehicles and long distance, high speed desert racing
These 3.0" diameter bypass shocks are equipped with a Piggyback reservoir and 2/3/4 external bypass tubes.
The PiggyBack tank is made of anodized 6063 aluminum, is lightweight and disperses heat quickly, plus it does not rust internally because it keeps the gas separate from the shock absorber oil, thus avoiding the emulsion effect that temporarily inhibits the effectiveness of the shock absorber. In this model, the gas canister is attached to the head of the shock absorber, avoiding having tubes running under the wheel arches with risk of contact with the tires.
As soon as your order is placed, one of our shock tune-up experts will review your shock specifications and contact you to finalize the order details.
All King shocks are available with standard or custom tuning. For custom tuning, one of our shock absorber experts will work with you to make sure your shocks are built perfectly for your car to provide the best balance of performance and ride quality.
We will also help you determine the best bypass tube arrangement and configuration for your vehicle. Our standard calibration is calculated to work well for most typical suspensions that use shocks of this size.
Features
- cadmium plated chrome body, precision bored and polished
- 1" shaft heat treated, hard chrome plated and micro polished
- precise, high-flow, low-profile adjustable bypass valves
- aircraft-grade billet aluminum components
- heat-treated 6061 aluminum alloy piston
- heat-treated stainless alloy valve shims
- teflon bronze composite wear band
- replaceable 1/2" Teflon-coated spherical bearings
- lightweight hard anodized aluminum reservoirs
- long-lasting urethane seals
- high-quality Parker pipe fittings
- replaceable 5/8" Teflon lined spherical bearings
- fully serviceable
- manufactured in the United States
Shock absorber specifications
Below are shock absorber details for all standard size 2.0 bypass shocks:
- stroke 8" - length in compression 16.70" - length in extension 24.70"
- stroke 10" - length in compression 18.70" - length in extension 28.70"
- stroke 12" - length in compression 20.70" - length in extension 32.70"
- stroke 14" - length in compression 23.45" - length in extension 37.45"
- stroke 16" - length in compression 26.20" - length in extension 42.40"
- stroke 18" - length in compression 28.95" - length in extension 46.95".
Compressed and extended shock lengths are measured from eye to eye. Some shock absorber options may change the dimensions.
By looking at the image below choose, through the menus at the top, how you want the ByPass tubes positioned:
In the first style the ByPass hoses are at the side of the reservoir, in the second style the hoses are in front of the reservoir.
OPTIONS
The ByPass King shock absorber can be accessorized according to your needs either when ordering or later with the following accessories:
Wide spacers: you can choose the pin diameter and the width of attachment to the frame and the bridge;
External bump stop: it is possible to choose whether to insert a bumpstop made of rubber or polyurethane, higher and softer;
Rod end length: it is possible to install supports that connect the coilover stem to the bridge, 3 sizes over the standard;
Reservoir: it is possible to have the finned tank to better dissipate heat.
From the menu above make the choices to have the ideal configuration to your needs, if you have doubts contact us.
